Home > Shower Diverter > Shower Diverter Not Working Correctly

Shower Diverter Not Working Correctly

Contents

I have installed the new valve (an identical replacement to the old valve I removed from my shower) and I made sure that all connections were tight (i.e. Good work. I'm also a little confused as to why the water pressure should affect whether the water is being completely diverted from the tub faucet to the shower when the shower is I'm not sure if that means anything, but I thought I'd mention it in case it might have some relevance to this problem. http://vidivit.com/shower-diverter/shower-diverter-not-working.html

Please try and alter the pressure and see if a lower pressure makes the problem worse; conversely, the higher pressure MAY reduce the "leaking" through the spigot. Sorry, I can't give you any technical on this - but thought it might be worth a try. I am really at a loss as to why the new diverter valve does not seem to be working properly and I would greatly appreciate any information you might have regarding Search Google Answers for Goo

Shower Diverter Repair

As far as I can tell, the new diverter has been installed properly and it does shut off the shower completely when the handle is turned to the "OFF" position. Do you have any other ideas on what might be the problem with the shower not completely diverting? Thanks!

The diverter washer #18 is actually a threaded trim ring in this case used on a different trim style and not a part of the operating system of this stem. weisstho-ga Important Disclaimer: Answers and comments provided on Google Answers are general information, and are not intended to substitute for informed professional medical, psychiatric, psychological, tax, legal, investment, accounting, or other Clarification of Answer by jackburton-ga on 06 Dec 2002 05:43 PST any luck yet??? --jack Request for Answer Clarification by morpheus74-ga on 07 Dec 2002 16:48 PST I tried the waterproof Shower Diverter Stuck Up Position no leaks were detected in or around the new valve); however, I am still having a problem with the water not completely diverting from the tub faucet to the shower head

I have not found a reference to this type of issue in any plumbing manuals, etc. 3 Handle Shower Diverter Repair Please read carefully the Google Answers Terms of Service. Stock #17910 is the actual lower portion of this diverter stem but I think you may just need a thicker o-ring possibly on the bottom of this diverter and see if Let me know if this addresses the problem. --Jack Request for Answer Clarification by morpheus74-ga on 03 Dec 2002 06:30 PST Jack, I probably should have mentioned this in my original

Once I got the valve stems out the first time, I no longer felt this resistance during subsequent attempts to remove the stems from the pipe. Shower Pull Knob Comments Subject: Re: Repairing a shower diverter valve From: weisstho-ga on 03 Dec 2002 17:26 PST (i still think it may be the water pressure . . .) :-) I had a similar problem once, where my wife would just crack the hot and cold valves and complain that the water was still, to some extent, coming through the spigot, When I tried using the second shower, it now has almost the same problem with not completely diverting as the first shower - I did not change anything on the second

3 Handle Shower Diverter Repair

Clarification of Answer by jackburton-ga on 03 Dec 2002 07:50 PST I would try looking inside the valve body for wear or a crack but first I would try another diverter additional hints Subject: Re: Repairing a shower diverter valve From: weisstho-ga on 05 Dec 2002 14:05 PST Sure, be glad to. Shower Diverter Repair Thank you so much for your help and patience in providing me with the information I needed to fix my problem! How To Fix A Shower Diverter Gate Google does not endorse, and expressly disclaims liability for any product, manufacturer, distributor, service or service provider mentioned or any opinion expressed in answers or comments.

Looking forward to your reply. Check This Out As an experiment, I took a look at the other shower in my house which had a slight problem with not completely diverting (much less so than the shower I am Request for Question Clarification by weisstho-ga on 02 Dec 2002 20:15 PST Hello morpheus74! Higher pressure - no leak, low pressure - leak. Types Of Shower Diverters

I did notice, however, that both times when I removed the existing diverter valves that there was some resistance when I tried to pull the valve stems out of the pipe. If you can't alter the pressure at the tub effectively, perhaps limiting the flow at the meter shut-off for purposes of this test might work. I pulled the diverter out, examined it and put the same diverter stem back in. http://vidivit.com/shower-diverter/shower-tub-diverter-not-working.html Unfortunately, the new diverter valve did not come with any instructions or diagrams and I am unable to find any information on the manufacturer's website regarding this particular valve.

Also, the new diverter valve appears to have all washers and O-rings intact, including a 00 Flat Bibb washer at the end of the diverter valve, a #7 O-ring near the How Does A Shower Diverter Work I'll let you know if I am still having problems - thanks! First off, thanks for a wonderfully detailed question.

In addition, I have checked thoroughly to ensure that I don't have any clogs in the shower line and/or leaks around any of the shower valves.

View Question Q: Repairing a shower diverter valve ( Answered , 3Comments ) Question Subject: Repairing a shower diverter valve Category: Miscellaneous I was having problems with the water not completely diverting from the tub faucet to the shower head when I turned on the shower and I believed that replacing the diverter weisstho-ga Answer Subject: Re: Repairing a shower diverter valve Answered By: jackburton-ga on 03 Dec 2002 05:54 PST Rated: Hi morpheus74, I think you might need to replace your Shower Pull Knob Stuck Thank you for your time!

At least with that particular diverter, it seemed that the higher the pressure on the supply side of the diverter, the better it seated. I have read - can you please clarify this point? Clarification of Answer by jackburton-ga on 09 Dec 2002 05:22 PST I would check the o-rings on the outside of the diverter for possible nicks also clean the housing with some have a peek here morpheus74-ga rated this answer: I added a thicker O-ring to the diverter per the researcher's suggestion and it seemed to fix the problem.

Usually when I turn the shower on I have both water valves open all the way which should represent the maximum water pressure going to the shower. This is probably worn or nicked and is causing the bibb seat to not seat correctly. Unfortunately I am still not having any luck - I think what I may need is something called a diverter washer which was not included with the diverter when I bought The diverter washer I need for this stem is a #18, but I have had no luck finding one either online or in Home Depot.

General information on how replace a shower diverter valve is not useful to me - what I really need is some specific information that might help me figure out what I Have you varied the water pressure? If you feel that you have found inappropriate content, please let us know by emailing us at [email protected] with the question ID listed above. In any event, I guess my next step is to try to find a diverter washer for this stem and see if that makes a difference - any ideas on where

I would definitely use this service again in the future!