Home > How To > Some Xmas Lights Not Working

Some Xmas Lights Not Working


Works great. If the string is still dark, continue to the next step. Thank you, Was this answer helpful? Has anybody done this to a broken string of LED lights? check over here

Cancel mrbill97702 Rep: 1 Posted: 12/07/2013 Options Permalink History When only half the string lights up, it's usually because of a single light in the bad section. no filament. Unplug and flip plug 180 and replug and the other half comes on -- and the half that did work now does not. still use steel:(... 4). http://www.popularmechanics.com/home/how-to/a3231/how-to-fix-a-string-of-christmas-lights-14774047/

How To Fix Christmas Lights Half Out

For existing strings, there may be an option: If two or more strings were bought at the same time, we can take one out of service, put it in a zip Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? These lights came from Holiday Time LED mini light set (50 COUNT) purchased from Walmart. The actual failure turned out to be poor soldering and not component failure.

View the answer I have this problem too Subscribed to new answers Is this a good question? Actually replacing a fuse in these strings can be frustrating. Oturum aç 154 184 Bu videoyu beğenmediniz mi? How To Change Fuse In Christmas Lights This will make the lights unnoticeably dimmer.

Since 3 amps at 120V is 360 watts of power, it might seem that the AC outlet could support a lot of light strings, but that is deceptive. A loose bulb, broken socket or frayed wire is sometimes all it takes for the strand to malfunction. Yes No Voted Undo Score 7 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? this So, I am now searching for 5 replacement LED lights to see if multiple LED failures caused the problem.

If you have a string failure, best to cut your losses and go get yourself a new one. How To Fix Led Christmas Lights Crazy but this string too is an extra long set. SO, since i had an extra length of lights at the end of the run, I just pulled the dead light section aside and rehung the line starting at the lit Debra Carmona 13.050 görüntüleme 8:58 LED Christmas Light String Repair!! - Süre: 9:22.

How To Find The Bad Bulb On Christmas Lights

If you install a new one, make sure it has the proper voltage rating or you risk damaging the whole set. http://www.instructables.com/answers/Christmas-lights-arent-working-/ Cancel Mark Makarenko Rep: 1 Posted: 11/28/2013 Options Permalink History the same thing happened to me. How To Fix Christmas Lights Half Out I replaced it. How To Replace Christmas Light Bulb So much for 'LED's save money' !

She said you just have to follow the directions and it will tell you what to do. If it is a blown fuse wouldn't the whole string be burnt out? Modern hum-tracers (and the LIGHTkeeper PRO) have little tin cutouts which are supposed to help lever the bulb out of the socket. We will not maintain any record of these emails. Light Keeper Pro

You might also want to check the fuses - most light sets have the tiny fuses somewhere in the plug. You may also just go ahead and replace them since they are not to expensive. Cancel alicegwyn Rep: 1 Posted: 11/01/2011 Options Permalink History How do you open and check the fuses? http://vidivit.com/how-to/some-christmas-tree-lights-not-working.html direct current.

Most strings include one or two spare fuses, which can be replaced in the plug. How To Test Christmas Lights Without A Tester A shorted bulb in one of your strings most likely caused a failure in a diode that changes that 110v AC to DC . They also usually close with a “Don’t use my method or your house may burn down .”, disclaimer .

On closer inspection, I did find a few with broken bulbs and once replaced, the strings lit up.

Good luck!Ad ReplyWas this helpful?Helpful? Undo Sandi_W So sorry this has happened to you. Replace the LED's back into the sockets, push the securing tab down and your new corrosion proofed lights should last a very long time time. How To Fix Christmas Tree Lights Half Out Next time I see it I will pick it up.

Those were plugged into one socket of an outlet. This change can be verified with a magnet, and is probably at least partly responsible for LED string prices not having dropped as fast as we expected over the years. It costs roughly $20 US, so this may not be worth it if you only have a couple strings of lights. Normally the bulbs have a "shunt" which shorts the bulb when it experiences full line voltage.

Was this answer helpful? Was this answer helpful? I'm sure glad I used 'Home Hardware's SCREW in C-9's when I replaced all my 'main string' big bulb's ! This often happens when too many strings are connected end-to-end.

The hum detector has to be pretty good to show the difference between a hot wire and one which acts an antenna to pick up the hum normally around us. If you're lucky, simply plugging in the mini lights will reveal a bad bulb. "Bad" may just mean it needs to be seated more firmly in its socket. I don't know why anyone in their right mind would bother to buy these lights! She purchased in HD or Lowe's.

You can change this preference below. Things You'll Need Fuse Replacement Screwdriver Replacement fuses Finding the Dead Bulb Christmas tree repair tool or non-contact voltage detector DIY Button-operated lighter Light Bulb Replacement Replacement bulbs Rarely: Wire cutters I am not sure where you are located but I get my replacement fuses at Walmart and its a lot cheaper and less time consuming to start with that. I get really frustrated when they are working and then you put them on the tree and get all the lights on and some strands go out.

Pry apart the plastic cover, then lift out the igniter with a pair of needle nose pliers.[8] The piezo igniter includes a button, and two tiny metal or plastic prongs. So if we look for the two-wire section in the middle, we can cut there (after first turning the power off). DONT FORCE IT IN'IF ITS TIGHT THEN TURN IT ROUND AND THAT SHOULD SOLVE THE PROBLEM' MERRY XMAS' 12/16/2015 by alcopusher Add a comment 0/1024 Cancel Post comment Are you sure Was this answer helpful?

You can fix a faulty shunt with the LightKeeper Pro. You should find two of them in there. Was this answer helpful?